The main purpose of the electronic diesel fuel pump seal is to isolate the contact between the oil vapor and the spark. Specific sealing parts include computer control box, computer box and mechanical box separator and explosion-proof junction box.
The above-mentioned sealing parts mainly use rubber strips, rings, etc., by the climate and the impact of the scene, rubber products will appear thermal expansion and contraction, aging cracking to seal failure. Therefore, it should be in accordance with the daily inspection requirements of regular inspection.
1. Computer cover and installed in the panel on the components and the lid between the seal, shall not appear notch, deformation and obvious different thickness.
2. Computer box and mechanical box between the partition cable, pipe through, the seal can not be loose, deformation and fall off, check the feel must be tight, strong.
3. Strong, weak explosion-proof junction box is generally in the bottom of the gas station management software oil vapor often gathered in the place, the seal by the seal and bolts to protect. Therefore, it is necessary to ensure that the seal is complete and bolted.
The temperature probe is generally a thermocouple or RTD, thermocouple temperature voltage changes, the thermal resistance temperature resistance change, that is good.
2017年9月15日星期五
2017年9月9日星期六
The marine fuel dispensers circuit includes power, control, pulse, display and lightning protection, anti-static circuit, which mine, anti-static circuit is the focus of attention.
Circuit hidden trouble is not easy to detect, because the electricity is invisible, in addition to the occurrence of power short circuit, circuit or voltage instability, etc., will cause the fuel dispensing meters dysfunction and was found, the electrostatic ground contact bad or virtual connection, usually does not fail , And by the human senses can not be judged, so easy to be ignored. Therefore, we must use a multimeter, according to the provisions of the time interval to detect, the general site refueling gun to detect once a month is appropriate, the seaside and more serious corrosion areas, should improve the detection frequency to once every half months.
Circuit hidden trouble is not easy to detect, because the electricity is invisible, in addition to the occurrence of power short circuit, circuit or voltage instability, etc., will cause the fuel dispensing meters dysfunction and was found, the electrostatic ground contact bad or virtual connection, usually does not fail , And by the human senses can not be judged, so easy to be ignored. Therefore, we must use a multimeter, according to the provisions of the time interval to detect, the general site refueling gun to detect once a month is appropriate, the seaside and more serious corrosion areas, should improve the detection frequency to once every half months.
2017年9月3日星期日
Self-service tanker use steps:
In the fuel transfer hand pump before the need to pay attention to the car to find the oil gun before the label, to avoid the wrong oil,
1, hand touch static electricity
In accordance with the fuel instructions, the first step should be placed in an electrostatic discharge area, the body may eliminate the existence of static electricity, to avoid the danger caused by refueling.
2, set the amount of fuel
The second step is to set the amount of fuel.If you use the fuel card refueling, insert the fuel card directly, and click on the screen "fuel card" option. At this point the side of the screen will display the card balance, we can according to their own needs Select a fixed amount or fixed fuel two modes. After selecting the click button to start the refueling.
If we use the cash to refuel, you have to see the instructions on the tanker, use the specified face value for temperature probe calibration, while the notes are not too old, otherwise many machines will not recognize the input banknotes and enter the amount can start refueling, the process Feeling and using ordinary drink vending machines are not much different.
3, began to refuel
Refueling process is not difficult, off the car, open the fuel tank cover, pull out the fuel tank into the fuel tank, press the handle to start automatically refueling, this process is fully automatic, refueling to achieve the default amount will automatically jump gun, no If you need to put the refueling gun back to the tanker to complete the refueling.
At the same time to remind the oil guns have a fixed locking device, refueling process without manual press, but each gas station oil guns will be nuanced, this need to show the specific circumstances, but even if the lock mechanism is not found Worry, manually press the same fuel can be safely operated, to achieve the default amount of oil gun will automatically stop refueling.
1, hand touch static electricity
In accordance with the fuel instructions, the first step should be placed in an electrostatic discharge area, the body may eliminate the existence of static electricity, to avoid the danger caused by refueling.
2, set the amount of fuel
The second step is to set the amount of fuel.If you use the fuel card refueling, insert the fuel card directly, and click on the screen "fuel card" option. At this point the side of the screen will display the card balance, we can according to their own needs Select a fixed amount or fixed fuel two modes. After selecting the click button to start the refueling.
If we use the cash to refuel, you have to see the instructions on the tanker, use the specified face value for temperature probe calibration, while the notes are not too old, otherwise many machines will not recognize the input banknotes and enter the amount can start refueling, the process Feeling and using ordinary drink vending machines are not much different.
3, began to refuel
Refueling process is not difficult, off the car, open the fuel tank cover, pull out the fuel tank into the fuel tank, press the handle to start automatically refueling, this process is fully automatic, refueling to achieve the default amount will automatically jump gun, no If you need to put the refueling gun back to the tanker to complete the refueling.
At the same time to remind the oil guns have a fixed locking device, refueling process without manual press, but each gas station oil guns will be nuanced, this need to show the specific circumstances, but even if the lock mechanism is not found Worry, manually press the same fuel can be safely operated, to achieve the default amount of oil gun will automatically stop refueling.
2017年8月28日星期一
Analyze and summarize the common faults, and then solve the problem.
First: small flow is not self-styled
The reason is that in the small gasoline flow meter, the flow rate is low, the suction effect is small, the pressure difference between the upper and lower chamber of the switch film is small, can not overcome the elasticity of the spring so that the self- To solve this problem, it is necessary to reduce the spring force of the spring.
Second: refueling guns are not self-styled
The reason for this is that the upper surface of the diaphragm is sealed with the outside, for example, the upper part of the plastic cap is not tightened, and the "O" type seal on the adapter and the sub-seat of the oil gun is damaged. The diaphragm can not form a pressure difference. To solve this problem need to tighten the plastic cover pressure wire, replace the "O" seal.
Third: refueling guns often self-styled
The reason is that the nozzle inside the electronic diesel fuel pump is blocked by foreign body, poor air intake or open the membrane on the cavity of the spring caused by the spring is too small. Solution: clear the foreign body in the intake pipe, stretch the spring to enhance the elasticity.
The reason is that in the small gasoline flow meter, the flow rate is low, the suction effect is small, the pressure difference between the upper and lower chamber of the switch film is small, can not overcome the elasticity of the spring so that the self- To solve this problem, it is necessary to reduce the spring force of the spring.
Second: refueling guns are not self-styled
The reason for this is that the upper surface of the diaphragm is sealed with the outside, for example, the upper part of the plastic cap is not tightened, and the "O" type seal on the adapter and the sub-seat of the oil gun is damaged. The diaphragm can not form a pressure difference. To solve this problem need to tighten the plastic cover pressure wire, replace the "O" seal.
Third: refueling guns often self-styled
The reason is that the nozzle inside the electronic diesel fuel pump is blocked by foreign body, poor air intake or open the membrane on the cavity of the spring caused by the spring is too small. Solution: clear the foreign body in the intake pipe, stretch the spring to enhance the elasticity.
2017年8月22日星期二
Analyze the precautions regarding the use of the dispenser valve.
1, please do not apply fluid other than fluid.
2, do not use the maximum use of pressure restrictions.
3, do not use outside the use of temperature range, to prevent the sealing material caused by wear or leakage.
4, do not carry out artificial hit, bending, stretching, to prevent damage caused.
5, do not mix in metal powder or sand dust and other diesel fuel flow meter to use, to prevent poor work or leakage.
6, the installation of the thread, do not exceed the maximum tightening torque installed to prevent damage caused.
7, do not use cracks with the hose, to prevent leakage or fall off.
8, such as for vibration, the impact of the machine will cause reduced durability.
2, do not use the maximum use of pressure restrictions.
3, do not use outside the use of temperature range, to prevent the sealing material caused by wear or leakage.
4, do not carry out artificial hit, bending, stretching, to prevent damage caused.
5, do not mix in metal powder or sand dust and other diesel fuel flow meter to use, to prevent poor work or leakage.
6, the installation of the thread, do not exceed the maximum tightening torque installed to prevent damage caused.
7, do not use cracks with the hose, to prevent leakage or fall off.
8, such as for vibration, the impact of the machine will cause reduced durability.
2017年8月16日星期三
What are the working materials for the tanker?
First, the oil marine fuel dispensers
1. Small tanker after the gun, the signal sent to the electrical room of the electromagnetic switch
2. Electromagnetic switch action, the 220V power supply to the sinking pump
3. After the oil pump moves, the oil is piped to the tanker
4. The oil of the small tanker is filtered by the filter and flows into the flowmeter when the solenoid valve is opened
5. After the oil flow meter:
(1) oil along the leather tube, from the device, oil gun out of oil. (2) flow meter action, the pulse generator to send signals to the electronic board measurement
Second, self-priming retail fuel dispensers
1. Small tanker after the gun, the signal sent to the tanker electronic board
2. Small tanker electronic board to send signals to the motor power board
3. Motor power supply (110V or 220V) to the motor
4. After the motor action to drive the pump, the pipeline will be oil from the tank to the tanker
5. After the oil is filtered through the filter, when the solenoid valve opens and flows to the flowmeter
6. After the oil flow meter: (1) oil along the hose, from the device, oil gun out of oil. (2) After the flowmeter moves, the signal is transmitted by the pulse generator
automatic fuel dispenser by the computer will be stuck ash processing after the boot signal to start the motor, and the measurement of the original data back to zero, while the motor drive pump rotation, the oil into the oil and gas separator, separated by oil and gas, into the The meter measures and delivers oil to the oil container through the hose and oil gun.
1. Small tanker after the gun, the signal sent to the electrical room of the electromagnetic switch
2. Electromagnetic switch action, the 220V power supply to the sinking pump
3. After the oil pump moves, the oil is piped to the tanker
4. The oil of the small tanker is filtered by the filter and flows into the flowmeter when the solenoid valve is opened
5. After the oil flow meter:
(1) oil along the leather tube, from the device, oil gun out of oil. (2) flow meter action, the pulse generator to send signals to the electronic board measurement
Second, self-priming retail fuel dispensers
1. Small tanker after the gun, the signal sent to the tanker electronic board
2. Small tanker electronic board to send signals to the motor power board
3. Motor power supply (110V or 220V) to the motor
4. After the motor action to drive the pump, the pipeline will be oil from the tank to the tanker
5. After the oil is filtered through the filter, when the solenoid valve opens and flows to the flowmeter
6. After the oil flow meter: (1) oil along the hose, from the device, oil gun out of oil. (2) After the flowmeter moves, the signal is transmitted by the pulse generator
automatic fuel dispenser by the computer will be stuck ash processing after the boot signal to start the motor, and the measurement of the original data back to zero, while the motor drive pump rotation, the oil into the oil and gas separator, separated by oil and gas, into the The meter measures and delivers oil to the oil container through the hose and oil gun.
2017年8月10日星期四
Tanker tanker used;
(1) on-board pump refiner Oil and gas separator is equipped with a filter, which consists of copper wire mesh and felt mesh sets, the separator side wall has a triangular cover can remove the filter. The filter of the combined pump refiner is installed in the inlet port. Submersible pump type tanker installed with a special filter box, open the end cap to remove the filter. The filter should be cleaned regularly (at least once a month) with gasoline to clean the copper mesh cover, damage should be replaced, and remove dirt from the oil machine to protect the pump and flow meter.
(2) gas station management software and the combination of the pump on the relief valve adjustment screw used to adjust the pump pressure, and then adjust the tanker's oil discharge. Factory has been adjusted. After long-term use, such as the amount of oil dropped, the adjustment screw can be tightened in order to increase the pressure of the pump, but not more than 0.3MPa, so that the amount of oil to meet the requirements.
(3) Combination of pump-type tanker is only suitable for underground tanks, such as the use of high oil tank, there will be exhaust pipe oil phenomenon, then be sure to block the exhaust pipe.
(4) the use of oil guns to avoid the oil gun with the oil pipe percussion by oil containers, press the switch and other abnormal operation, so as not to damage the electronic diesel fuel pump, causing oil spills. To check regularly, tighten the screw on the tubing to prevent the oil pipe root loose, damaged, underground storage tank regularly cleaned to keep the oil clean.
(5) the accuracy of the adjustment of the machine should be "JJG443-86 metering tanker test procedures," the relevant provisions.
(6) overhaul the electrical part of the power must be cut off, should not take electricity repair. Do not damage the explosion-proof surface when opening the explosion-proof case. When the explosion of dust inside the dust should be clean, the cable seal should be good, metal pads, gaskets can not be lost, the number of screws is not missing, tightened to ensure that the electrical components of the explosion-proof performance.
(1) on-board pump refiner Oil and gas separator is equipped with a filter, which consists of copper wire mesh and felt mesh sets, the separator side wall has a triangular cover can remove the filter. The filter of the combined pump refiner is installed in the inlet port. Submersible pump type tanker installed with a special filter box, open the end cap to remove the filter. The filter should be cleaned regularly (at least once a month) with gasoline to clean the copper mesh cover, damage should be replaced, and remove dirt from the oil machine to protect the pump and flow meter.
(2) gas station management software and the combination of the pump on the relief valve adjustment screw used to adjust the pump pressure, and then adjust the tanker's oil discharge. Factory has been adjusted. After long-term use, such as the amount of oil dropped, the adjustment screw can be tightened in order to increase the pressure of the pump, but not more than 0.3MPa, so that the amount of oil to meet the requirements.
(3) Combination of pump-type tanker is only suitable for underground tanks, such as the use of high oil tank, there will be exhaust pipe oil phenomenon, then be sure to block the exhaust pipe.
(4) the use of oil guns to avoid the oil gun with the oil pipe percussion by oil containers, press the switch and other abnormal operation, so as not to damage the electronic diesel fuel pump, causing oil spills. To check regularly, tighten the screw on the tubing to prevent the oil pipe root loose, damaged, underground storage tank regularly cleaned to keep the oil clean.
(5) the accuracy of the adjustment of the machine should be "JJG443-86 metering tanker test procedures," the relevant provisions.
(6) overhaul the electrical part of the power must be cut off, should not take electricity repair. Do not damage the explosion-proof surface when opening the explosion-proof case. When the explosion of dust inside the dust should be clean, the cable seal should be good, metal pads, gaskets can not be lost, the number of screws is not missing, tightened to ensure that the electrical components of the explosion-proof performance.
订阅:
博文 (Atom)






